HDR-15-24 electronic component is an ultra-thin DIN rail power supply with an output power of 15W, a voltage of 24V, and a current of 0.63A. This power supply has short-circuit, overload and overvoltage protection functions to ensure the safe and stable operation of the equipment.
About its application scenario:
HDR-15-24 electronic components are usually used in occasions that require stable and reliable power supply, such as industrial automation equipment, instrumentation, control systems, etc. Because of their various protection functions, they can be used in complex and changeable environments, such as high temperature, low temperature, high humidity, vibration and other environments.
When selecting the configuration, you need to consider the required power, voltage and current parameters to ensure that the HDR-15-24 electronic components can meet the actual needs. At the same time, factors such as its installation method, size and interface type need to be considered to ensure that it is compatible with the equipment used.
Notes on maintenance:
1. Regularly check the appearance of HDR-15-24 electronic components to ensure that there is no damage or deformation
2. Clean up the dust and debris around it regularly and keep it clean.
3. During use, check whether the temperature is normal regularly to avoid overheating and malfunction
4. If it is found that its performance parameters are abnormal, it should be repaired or replaced in time.
In short, the HDR-15-24 electronic component is a power supply with multiple protection functions, which can ensure the safe and stable operation of the equipment. When configuring selection and maintenance, its characteristics and requirements should be fully considered to ensure its normal operation and extend its service life.
Product Description: ·
Super design: width 17.5mm(1SU) international universal input 85-264VAC(277VAC available), no-load loss 0.3W · Class I isolation level, adjustable protection type of DC output voltage through LPS (limited power supply): short circuit/over load/over voltage natural air cooling (operating temperature: 30 ~ +70 C) can be installed on TS-35/7.5 or 15. Overvoltage level. LED indicates power supply start-up. 3-year warranty. Home control system. Building automation. Industrial control system. Factory automation. Electromechanical equipment characteristics: Application: File Name:HDR-15-SPEC 2021-06-07 Rated Power Output Voltage Series Name 15W Super Ladder DIN Rail Power Supply HDR-15 Series D0D 0D DD HDR-15 is an economical super-modeling 15W rail power supply conforming to German Industrial Standard, suitable for installation on TS-35/7.5 or TS-35/15 tracks, the body in the cabinet is designed to be 17.5mm(1SU) wide in space-saving space. The whole series adopts a full range of AC inputs from 85VAC to 264VAC(277VAC is also applicable) and all conform to BS ENEN61000-3-2 standards on harmonic current specifications specified by EU. The HDR-15 is designed with plastic shell, which can effectively prevent users from electrical hazards. The working efficiency is as high as 87%. Under the condition of air circulation, the whole series can work in the ambient temperature of-30C to 70C C. It has complete protection function and conforms to home automation. Relevant certification of industrial control equipment (EC6236801D UL508DUL6236801DBS EN/EN6155802016) makes HDR-15 a highly competitive power supply for household and industrial applications.
Electronic components
Quantity 100
Model Series HDR-15-24 HDR-15-5 HDR-15-12 HDR-15-15 HDR-15-48
HDR-15-24
RoHS(63X37) Yes
Minimum supply voltage 3.5V
Minimum operating temperature-40C
Maximum supply voltage 6.5V
Maximum operating temperature 100C
Length 3.3mm Width 2.8mm Height 1.5mm
HDR-15-24 switching power supply 24V0.6A15W ultra-thin ladder DIN switching power supply
HDR-15-24 switching power supply 24V/0.6A/15W ultra-thin stepped DIN rail transformer
HDR-15-24
Output:
DC voltage 24V
Rated current 0.63A
Current range 0 ~ 0.63A
Rated power 15.2W
Ripple and noise (max) Remarks 2 150mVp-p
Voltage adjustment range 21.6~29V
Voltage accuracy note 3+1.0%
Linear adjustment +1.0%
Load adjustment rate +1.0%
Start-up, rise time 2000ms,80ms/230VAC 2000ms,80ms/115VAC (at full load)
Holding time (Typ.)30ms/230 VA12ms/115VAC (at full load
Input:
Voltage range 85 ~ 264VAC(277VAC available) 120 ~ 370VDC(390VDC available)
Frequency range 47~63Hz
Efficiency (Typ.) 80% 85% 85.5 86% 87%
AC Current (Typ.)0.5A/115VAC0.25A/230VAC
Inrush Current (Typ.) Cold Start 25A/115VAC 45A/230VAC
Protect 110~145 of the rated output power of the overload when the output voltage is less than 50% when the hiccup mode, and can be automatically restored after the abnormal load condition is removed. The output voltage is constant current mode when the abnormal load condition is removed when the output voltage is 50% ~ 100 can be automatically restored after the abnormal load condition is removed.
Overvoltage 5.75~6.75V 14.2~16.2V 18.8~22.5V 30~36V 56.5~64.8V
Protection mode: turn off output, clamped by zener diode
Ambient operating temperature 30 ~ +70°C (please refer to the derating curve ") Operating humidity 20 ~ 90% RH, non-condensing storage temperature, humidity 40 ~ +85°C,10 ~ 95% RH, non-condensing temperature coefficient +0.03%/°C(0~50°C) Vibration resistance
10~500Hz,2G 10 minutes/cycle, X,Y, Z 60 minutes each; Installation: conform to the IEC60068-2-6 operating altitude of 2000 meters overvoltage class III; According to EN61558,EN50178,EN60664-1,EN62477-1; The altitude can be as high as 2000 meters
Safety specification UL62368-1, UL508, EAC TP TC 004, BSMI CNS14336-1, TUV BS EN/EN61558-2-16, BS EN/EN61558-1,IEC62368-1 approved, design reference TUV BS EN/EN62368-1
Withstand voltage I/P-O/P:4KVAC insulation impedance I/P-O/P:100M Ohms / 500VDC / 25 ℃/ 70% RH
Electromagnetic Compatibility Emission Parameter Standard Test Level / Note
Conducted BS EN/EN55032(CISPR32), CNS13438 Class B
Radiated BS EN/EN55032(CISPR32), CNS13438 Class B
Harmonic Current BS EN/EN61000-3-2 Class A
Voltage Flicker BS EN/EN61000-3-3 -------
Safety regulations and electromagnetic compatibility (Note 4)
Electromagnetic Compatibility Immunity
BS EN/EN55024, BS EN/EN55035, BS EN/EN61000-6-2, BS EN/EN61204-3
ESD BS EN/EN61000-4-2 Level 3, 8KV air; Level 2, 4KV
Radiated Susceptibility BS EN/EN61000-4-3 Level 3, criteria A
EFT/Burest BS EN/EN61000-4-4 Level 3, criteria A
Surge BS EN/EN61000-4-5 Level 4,2KV/L-N, criteria A
Conducted BS EN/EN61000-4-6 Level 3, criteria A
Magnetic Field BS EN/EN61000-4-8 Level 4, criteria A
Magnetic Field BS EN/EN61000-4-8 Level 4, criteria A BS EN/EN61000-4-11 >95% dip 0.5 periods, 30% dip 25 periods,>95% interruptions 250 periods
Other MTBF 3724.3K hrs min. Telcordia SR-332 (Bellcore) ; 1166.1K hrs min. MIL-HDBK-217F (25 ℃)
Size 17.5*90 * 54.5mm (W * H * D)
Packing 78g; 160pcs/13.5Kg/1.14CUFT
Note 1. Unless otherwise specified, all specifications are measured at an input of 230VAC, rated load and 25C ambient temperature.
2. Ripple and noise measurement method: a 12 "twisted pair is used, and the terminals are connected in parallel with 0.1u and 47uf capacitors to measure under 20MHZ bandwidth.
3. Accuracy: including setting error, linear adjustment rate and load adjustment rate.
4. The power supply is regarded as an independent component, but the final power supply still needs to be confirmed with the terminal equipment for electromagnetic compatibility. For instructions on how to do EMC testing, refer to EMI Testing of Component Power Supplies ".
5. When the altitude exceeds 2000 meters (6500 feet), the ambient temperature of the fanless model decreases according to the proportion of every 3.5/1000m, and the ambient temperature of the fan model decreases according to the proportion of every 5C/1000m.
X Product Disclaimer: For details, please refer
For more information, it is recommended to consult the relevant experts or consult the product manual
a lot of in stock
Welcome to buy